 FINDING CIRCUIT BREAKER |
|
| Use the tip of the Sniffer to scan the circuit breakers. Please note that the Sniffer is designed to be held vertically for the vertical circuit breakers and horizontally for the horizontal circuit breakers. |
|
| MAKE SURE ALL THE CIRCUIT BREAKERS ARE ON |
|
| For example, start scanning from the top left row, then go down etc. |
|
| But you can scan the breakers in any order. While you are scanning, observe the bar-graph and listen to the buzzer. |
|
| FINDING EARTH FAULT |
|
| To find an earth fault or the trace faulty wire, you must connect the transmitter in serie with the fault. For example, if you have a short between Line and Earth, but you don't know where the short is. |
|
| Connect the Transmitter, using and adaptor, in series, in the line. If the Protection device trips, then you will have to bypass the protection device for the duration of this test. Use the optional leads for this use. |
| The 188FFF is a Fuse and Fault Finder which comprises of two parts : The Receiver and the Transmitter |
| The Transitter draws a current from the mains supply circuit to whcih it is connected to the Signal Current from the Tx is at about 10 kHz. The Transmitter is powered by the mains and requires no batteries |
| The 10kHz signal current generated by the Transmitter is then searched (sniffed) by the Receiver to detect the Fuse, Circuit Breaker or the faulty circuit |
| The Receiver is a tuned circuit which has it's center frequency tuned to about 10kHz. The sensor is located in the tip of the Receiver |
| The amplitude of the received signal is shown on a bar-graph type LEDs |
| The more LEDs ON, the stronger the signal. The Receiver uses on 9V battery |
| SPECIFICATIONS | |
| RECEIVER | |
| Tuner Circuit Mid Frequency | 10kHz |
| Bar Graph Leds | 9 |
| Battery Indicator Led | 1 |
| On Button | 1 |
| Off Button | 1 |
| Buzzer | 1 |
| Auto-off (Min) Approx | 1 |
| Power Source | 9V (6F22 006P) x 1 battery |
| Dimensions | 200(L) x 50(W) x 40(H) mm |
| Weight | 112g |
| Material | Polycarbonate/ABS |
| TRANSMITTER | |
| Working Voltage | 110 to 240 Vac (50/60Hz) |
| Frequency of Sourced Signal | 10 kHz |
| Dimensions | 60 (L) x 50(W) x 30(H) mm |
| Weight | 134g |
| Connection | Specify type of plug |
SIÊU THỊ THIẾT BỊ ĐO QUANG MINH - CÔNG TY TNHH ĐẦU TƯ VÀ TT QUANG MINH
ĐT: 04.3873.0880 - Hotline: 090.400.3848 - Fax: 04.3873.0880
Email: kd@sieuthithietbido.com - Website: www.sieuthithietbido.com - www.sieuthithietbidienmay.net
By Siêu thị thiết bị đo Quang Minh
Siêu thị thiết bị điện máy Quang Minh: nhà cung cấp Thiết bị nhận dạng ngắt mạch SEW 188 FFF Chính hãng Giá rẻ nhất - Gọi ngay 04.3873.0880 - 090.400.3848
5 sao trên
1755 khách hàng bình chọn
Báo giá Thiết bị nhận dạng ngắt mạch (Circuit Breaker) SEW 188 FFF
Đặt hàng